The most important noise source in helicopter cabins is the gearbox. Comprehensive measurements have shown that the structure-born noise path via the gearbox struts is dominant. Active control of the structure-born noise by applying additional Control forces to the struts is therefore a promising concept to im prove the comfort for passengers and crew. Such an active vibration isolation system has been developed by Eurocopter Deutschland and the DaimlerChrysler research and technology group. The corresponding control function was implemented on a dSPACE prototyping system.
Actuator Concept
The applied actuators consist of an active layer of piezoelectric material (PZT = lead zirconate titanate) bonded directly onto the strut. This allows the introduction of longitudinal shear forces into the strut. By applying a control voltage between the outer and inner surface of the piezo layer, the piezo shell can be strained or contracted in the longitudinal direction. A division of the piezo electric layer into three segments along the circumference again allows the control of both longitudinal and lateral vibrations of the strut. This concept offers several advantages:
- Simplicity of design
- No need for a completely new strut design (PZT shells are only add-ons to production struts)
- Only a small weight penalty
- Low actuator costs
- Easy maintenance
Each strut comprises three piezo rows, i.e., three independent actuators.
Characteristics
- Active vibration isolation with active gearbox struts
- Controller and system identification on a dSPACE prototyping system
- Release of active vibration isolation as optional equipment planned
Control Concept
The gear meshing frequencies are usually 10 dB to 20 dB above the background noise level. Typically the frequency range of gearbox noise is between 700 Hz and 4 kHz. The gearbox generated noise is determined by the transmission ratios of certain stages of the gearbox and the engine rotary speed. The engine rotary speed is rather stable. Therefore, frequency variations are typically less than ±2%. Amplitude variations generated by varying loads are more crucial for the control system design. The control algorithm used for the tests is based on a narrowband, multi-channel filtered-x LMS algorithm that uses sine/cosine reference signals. The frequency of the sine/ cosine reference is generated according to the measured rotor shaft speed. This control algorithm takes into account measured transfer functions between all actuators and sensors to ensure stability of the control loop. The transmission system of helicopters typically consists of a total number of 7 gearbox struts, 4 z-struts, 2 x-struts and 1 y-strut. Sensors are 3-axis accelerometers at the mounting points of the struts to the cabin. This means that the controller should be able to handle 21 input and 21 output channels at sampling rates higher than 5 kHz. The control algorithm and also the identification of transfer functions have been implemented on a dSPACE prototyping system. Thanks to its excellent performance and scalability the dSPACE system was ideally suited to handle the control task. Not to forget the powerful dSPACE software environment. Even with a modified hardware environment the graphical user interface remains unchanged. As a typical result for a BK117 helicopter with a vibration isolation system with 12 actuators (z struts) and 21 sensors, the accelerations at the most important z struts are reduced by about 20 dB.
Conclusion
The active vibration isolation with active struts is a very challenging solution to reduce the noise level in a helicopter cabin by acting on the most annoying high tonal gear meshing noise. The high noise reduction capability of the system has been demonstrated by BK117 helicopter ground runs. A significant reduction of the tonal noise components in the interior sound field was demonstrated. The next development step is to prove the concept in flight tests. After an optimization and serialization phase, Eurocopter plans to offer the system as an optional equipment to the customer. And due to the successful control implementation we will apply dSPACE systems to future projects such as active noise control for jet engines.
About the Authors
Dr. R. Maier is employed at DaimlerChrysler AG in the department for Aeroacoustics FT1/AA.
Dr. M. Bebesel is employed at Eurocopter Deutschland GmbH Germany.
PUBLISHED IN DSPACE NEWS FALL 2000